Price Clear







Showing WATER DECALS product(s)

Showing 1 - 30 of 45 products

img
SAVERM8.90

Water Decal for MG 1/100 Blue Frame 2nd Revise Gundam

- Water Decal for MG 1/100 Blue Frame 2nd Revise Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
img
SAVERM8.90

Water Decal for HG 1/144 Gundam Heavyarms EW

- Water Decal for HG 1/144 Gundam Heavyarms EW
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
img
SAVERM8.90

Water Decal for MG 1/100 00 QAN[T] Gundam

- Water Decal for MG 1/100 00 QAN[T] Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
img
SAVERM8.90

Water Decal HG Beargguy III

- Water Decal for HG BEARGGUY III water decal
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
img
SAVERM8.90

Water Decal HG 1/144 00 QAN[T] Gundam

- Water Decal for HG 1/144 00 QAN[T] Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
img
SAVERM8.90

Water Decal for MG 1/100 GAT-X103 BUSTER Gundam

- Water Decal for MG 1/100 GAT-X103 BUSTER Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
img
SAVERM20.98

Water Decal for RG 1/144 Zgok Bronze Gold Color

- Water Decal for RG 1/144 Zgok Bronze Gold Color
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
img
SAVERM17.18

Water Decal PG 1/60 FX-550 SKY GRASPER

- Water Decal for PG FX-550 SKY GRASPER water decal
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 21 cm x 24 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM18.80
img
SAVERM13.98

Water Decal for PG 1/60 MBF-02 Strike Rouge Gundam

- Water Decal for PG 1/60 MBF-02 Strike Rouge Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11.5 cm x 13.5 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunpla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM10.00
img
SAVERM8.90

Water Decal for RG 1/144 FX550 Sky Grasper

- Water Decal for RG 1/144 FX550 SKY GRASPER water decal
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
img
SAVERM15.08

HG 1/144 STRIKE FREEDOM Metal Effect Water Decal

- Water Decal for HG 1/144 Strike Freedom Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 10 cm x 9 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM14.90
img
SAVERM8.90

Water Decal MG 1/144 Gundam Seed Blitz Gundam

- Water Decal for Water Decal MG 1/144 Gundam Seed Blitz Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
img
SAVERM8.90

Water Decal RG/ HG 1/144 00 QAN[T] Gundam

- Water Decal for RG/ HG 00 QAN[T] OO?Qan[T] 
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
img
SAVERM19.90

Water Decal for MG 1/100 RX-178 MK-II MK2 AEUG Gundam

- Water Decal for MG 1/100 RX-178 MK-II MK2 AEUG Gundam Water Decal
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 15 cm x 20 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM10.00
img
SAVERM10.00

[VT] Water Decal for Gundam Machine Nest Domain Base - S Size

[VT] Water Decal for Gundam Machine Nest Domain Base


This is a Water Decal for Gundam Machine Nest Domain Base Series
Small Size

RM8.00
img
SAVERM14.00

[VT] Water Decal for Gundam Machine Nest Domain Base - L Size

[VT] Water Decal for Gundam Machine Nest Domain Base


This is a Water Decal for Gundam Machine Nest Domain Base Series
Large Size

RM10.00
img
SAVERM3.00

[Amex] Fluorescent Water Decal for MR Model (MJH) HIRM alike 1/100 Gundam Astray Noir

[Amex] Fluorescent  Water Decal for MR Model (MJH) HIRM alike 1/100 Gundam Astray Noir

This is a High Quality Fluorescent  Water Decal by AMAX and it is not a sticker. 

- Special design for HIRM alike 1/100 Gundam Astray Noir
- Best use with Mr Hobby Mr. Mark Setter
- Not pre-cut decal as the Bandai water decal slide
- Extra touch of detail for modeling kits

RM16.90
img
SAVERM11.18

[Water Decal] MG RX-93-2 Hi-V Gundam Titanium Gold Mark

  • Titanium Gold Mark Decal
  • Water decal for MG RX-93-2 Hi-V Gundam 
  • Not pre-cut like the bandai slide water decal
  • Extra touch of detail for modeling kits

RM18.80
img
SAVERM11.18

[Water Decal] MG RX-93-2 Hi-V Gundam Titanium Silver Mark

  • MG RX-93-2 Hi-V Gundam Titanium Silver Mark Decal

RM18.80
img
SAVERM17.18

[Water Decal] PG MBF-P01 Astray Red Frame

  • 14 cm x 21 cm
  • PG MBF-P01 ASTRAY RED FRAME water decal

RM18.80
img
SAVERM17.08

[Water Decal] PG GN-0000+GNR-010 00 Raiser Gundam

  • 21 cm x 15 cm
  • PG GN-0000+GNR-010 00 Raiser Gundam Water decal
  • Water decal for MG Unicorn Gundam 02 Banshee
  • Not pre-cut like the bandai slide water decal
  • Extra touch of detail for modeling kits

RM18.90
img
SAVERM3.10

HD MG Strike Rouge Ver RM metallic decal

  • Dimension 14 cm x 9 cm
  • HD MG Strike Rouge Ver RM metallic decal

RM14.90
img
SAVERM5.90

[Water Decal] MG 1/100 Freedom Gundam 2.0

  • MG Freedom Gundam 2.0 water decal

RM12.10
img
SAVERM6.80

[Water Decal] RG/HG 1/144 Sinanju

RG/HG 1/144 Sinanju Water Decal

RM13.10
img
SAVERM11.50

[Water Decal] SD Nightingale

Water Decal that special design for SD Nightingale.

RM13.10
img
SAVERM12.70

[Water Decal] Tekkadan Logo

Tekkadan Logo Water Decal

RM11.90
img
SAVERM10.00

[Water Decal][Da Lin] UC0079 (C005)

[Da Lin] UC0079 Water Decal (C005)


This is a High Quality Water Decal by Dalin and not a sticker. 

- Water decal for MG Unicorn Gundam 02 Banshee
- Not pre-cut like the Bandai slide water decal
- Extra touch of detail for modeling kits

RM11.90
img
SAVERM5.80

[Water Decal] MG ZGMF-X19A Infinite Justice Gundam

  • Water decal for MG Infinite Justice Gundam
  • Not pre-cut like the bandai slide water decal.
  • Extra touch of detail for modeling kits

RM12.10
img
SAVERM4.90

[Water Decal] HG Unicorn Banshee Gundam (Silver)

HG Unicorn Banshee Gundam water decal

RM13.00
img
SAVERM14.90

Bandai Water Decal for Macross Frontier HG 1/100 YF-29 Durandal Valkyrie (for the Maximilian Genus Custom Full Set Pack)

This is a sheet of water-slide decals, dry transfers, or self-adhesive stickers for use in detailing anime or science-fiction kits.

This set of decals was made especially for Bandai's 1/100 HG YF-29 Durandal Valkyrie (Maximilian Genus Custom) Full Set Pack model kit! Decals are included for all three forms: Battroid, Gerwalk and Fighter. Order yours today!

RM27.00

Showing 1 - 30 of 45 products