Price Clear







Showing Gundam Parts + WATER DECALS / STICKERS product(s)

Showing 421 - 450 of 498 products

img
SAVERM8.09

1/144 Scale Earth Federation Decal Sheet

  • Gundam decal sheet recommended for use on HGUC Gundam RX78-2, Guncannon and Guntank kits.

RM3.90
img
SAVERM7.50

Tamiya 87135 Mark Fit (Strong) Decal Solution 40ml Bottle

【 Perfect Decal Application 】   


Mark Fit enables perfect decal applications. It softens decals so they can easily fit to uneven, rounded, and matt finish surfaces of plastic models while increasing adhesion. The bottle's cap comes with a convenient brush. 1 bottle contains 40ml.

≪How to use≫
1. Apply Mark Fit to the model where decal is applied.
2. Place decal on the model.
3. Position decal by an wetting finger.
4. Press decal down gently with a soft cloth or cotton swab until excess water is gone.
5. Apply Mark Fit over the decal, then press down gently with a soft cloth or cotton swab.
6. Allow the decal to completely dry.

RM17.50
img
SAVERM8.90

Tamiya 87102 Mark Fit Decal Solution 40ml Bottle

" Perfect Decal Application "


Mark Fit enables perfect decal applications. It softens decals so they can easily fit to uneven, rounded, and matt finish surfaces of plastic models while increasing adhesion. The bottle's cap comes with a convenient brush. 1 bottle contains 40ml.

-  How to use -
1. Apply Mark Fit to the model where decal is applied.
2. Place decal on the model.
3. Position decal by an wetting finger.
4. Press decal down gently with a soft cloth or cotton swab until excess water is gone.
5. Apply Mark Fit over the decal, then press down gently with a soft cloth or cotton swab.
6. Allow the decal to completely dry.

RM17.00
img
SAVERM5.80

[WATER DECAL] MG Strike Freedom

  • water decal for 1/100 strike freedom gundam
  • not pre-cut like the bandai slide water decal.

RM12.10
img
SAVERM3.90

[Water Decal] HG Astray Red Frame Kai

  • water decal for gundam astray red frame gundam kai scale 1/144
  • not pre-cut like the bandai slide water decal.
  • extra touch of details for modeling kits.

RM9.10
img
SAVERM5.80

[Water Decal] RG Gundam 00 Raiser

  • water decal for 00 RAISER model kit scale 1/144.
  • not pre-cut like the bandai slide water decal.

RM12.10
img
SAVERM5.80

[Water Decal] RG ZGMF-X20A STRIKE FREEDOM Model Kit

  • Third Party Water decal for RG Strike Freedom model kit scale 1/144.

RM12.10
img
SAVERM5.80

[Water Decal] RG WING ZERO EW Model Kit

  • water decal for RG Wing Zero EW model kit scale 1/144.
  • not pre-cut like the bandai slide water decal.
  • It's recommended to use this tool when working on decalling: Cutting Matt, Tweezer, Empty swallow bottle with water, hobby k-nife, softening solution.
  • Apply a clear gloss surface before applying decal would be a good choice.

RM12.10
img
SAVERM11.00

PG Strike Freedom model kit gold color decal

  • Gold color decal for PG Strike Freedom Gundam Model kit.
  • Not pre-cut like the bandai slide water decal.
  • Extra touch of details for modeling kit

RM18.90
img
SAVERM5.89

[Water Decal] MG ZGMF-X42S Destiny Gundam Water Decal

- Water decal for HG / MG warning sign water decal - RED color
- Not pre-cut like the bandai slide water decal
- Extra touch of details for modeling kit

RM12.10
img
SAVERM5.89

[WATER DECAL] MG PMX-003 The-o

[WATER DECAL] MG PMX-003 The-o

RM12.10
img
SAVERM15.48

[Water Decal] Z260 MG Duel Assault Gundam GAT-X102 Water Decal

- Water decal for MG Duel Assault Gundam 
- Not pre-cut like the bandai slide water decal.
- Extra touch of detail for modeling kits

RM14.50
img
SAVERM5.89

[Water Decal] HG RX-0 Unicorn Water Decal

  • Water decal for HG RX-0 Unicorn water decal
  • not pre-cut like the bandai slide water decal.
  • extra touch of detail for modeling kits

RM12.10
img
SAVERM4.99

[Water Decal] MG 1/100 Aile Strike ver RM

  • Water decal for HG / MG warning sign water decal - RED color
  • Not pre-cut like the bandai slide water decal
  • Extra touch of details for modeling kit

RM13.00
img
SAVERM14.88

[Water Decal] RG RX-178 MK-II MK2 AEUG Gundam

Water slide decals to be used with various model kits. Contains markings that can be used with its specific character or at your discretion for customizing your own kits!

RM9.10
img
SAVERM17.18

MG 00 Raiser Gundam Silver Decal

  • silver color decal for MG 00 Raiser Gundam

RM18.80
img
SAVERM8.90

Water Decal for RG 1/144 FX550 Sky Grasper

- Water Decal for RG 1/144 FX550 SKY GRASPER water decal
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
img
SAVERM3.10

HD MG Strike Rouge Ver RM metallic decal

  • Dimension 14 cm x 9 cm
  • HD MG Strike Rouge Ver RM metallic decal

RM14.90
img
SAVERM5.90

[Water Decal] MG 1/100 Freedom Gundam 2.0

  • MG Freedom Gundam 2.0 water decal

RM12.10
img
SAVERM13.90

HG 1/100 VF-25F Messiah Valkyrie (Alto Saotome's) Special Water Transfer Decal

These waterslide decals were made especially for Bandai's 1/100-scale HG model kit of the VF-25F Messiah Valkyrie piloted by Alto Saotome from "Macross Frontier!" The set is compatible with all three forms: Battroid, Gerwalk, and Fighter. Place your order today!

RM28.00
img
SAVERM8.00

[Da Lin] Water Decal for MG 1/100 Unicorn + MS Cage

[Da Lin] Water Decal for MG 1/100 Unicorn + MS Cage

This is a High Quality Water Decal by Da Lin and it is not a sticker.

- Suitable for MG 1/100 Unicorn + MS Cage

- Best use with Mr Hobby Mr. Mark Setter
- Not pre-cut decal as the Bandai water decal slide
- Extra touch of detail for modeling kits- Product from Hong Kong

RM10.00
img
SAVERM14.90

Bandai Water Decal 30MS Minutes Sister Water Transfer Decals Vol.2

This is a sheet of water-slide decals, dry transfers, or self-adhesive stickers for use in detailing anime or science-fiction kits.

- Best use with Mr Hobby Mr. Mark Setter
- Not pre-cut decal as the Bandai water decal slide
- Extra touch of detail for modeling kits

RM21.00
img
SAVERM9.90

[Water Decal][BANDAI] Gundam Decal (RG) for God Gundam #138

Decals the marking of RG God model kits
Brand : Bandai

  • Cut out desired decal.
  • Dip decal and backing in water. Leave submerged 10-30 seconds.
  • Remove decal from water with tweezers.
  • Gently lift decal off of paper backing with tweezers.
  • Place decal in desired location on model, adjusting with cotton swab if necessary.
  • Apply Mark Setter or Mark Softer as needed.

RM20.00
img
SAVERM11.00

[Water Decal][BANDAI] Gundam Decal No#136 Mobile Suit Gundam Side Stories 1

New to the "Gundam Decal" line up comes a sheet of water transfer decals that can be used for 1/144 scale!

Versatile water transfer decals that include markings for unit insignia.

[Accessories]:
- Water transfer type decal x 1

RM18.90
img
SAVERM11.00

Bandai Water Decal #129 for HG 1/144 Nightingale

Decals the marking of HG 1/144 Nightinggale Gundam model kits
Brand : Bandai
  • Cut out desired decal.
  • Dip decal and backing in water. Leave submerged 10-30 seconds.
  • Remove decal from water with tweezers.
  • Gently lift decal off of paper backing with tweezers.
  • Place decal in desired location on model, adjusting with cotton swab if necessary.
  • Apply Mark Setter or Mark Softer as needed.

RM18.90
img
SAVERM11.00

[Water Decal][BANDAI] Gundam Decal (RG) for Hi-Nu Hi-v Gundam #132

Decals the marking of RG Hi-Nu Gundam model kits
Brand : Bandai

  • Cut out desired decal.
  • Dip decal and backing in water. Leave submerged 10-30 seconds.
  • Remove decal from water with tweezers.
  • Gently lift decal off of paper backing with tweezers.
  • Place decal in desired location on model, adjusting with cotton swab if necessary.
  • Apply Mark Setter or Mark Softer as needed.

RM18.90
img
SAVERM5.00

Bandai Water Decal for Macross Frontier HG 1/100 YF-29 Durandal Valkyrie (Saotome Alto Machine)

These new waterslide decals are made especially for Bandai's new HG model kit of Alto Saotome's YF-29 Durandal Valkyrie from "Macross Frontier"! 

Decals are included for all three forms -- Battroid, Gerwalk and Fighter. Order yours now!

RM27.00
img
SAVERM11.00

[Water Decal][BANDAI] Gundam Decal (RG) for Force Impulse Gundam #130

Decals the marking of RG Force Impulse model kits
Brand : Bandai

  • Cut out desired decal.
  • Dip decal and backing in water. Leave submerged 10-30 seconds.
  • Remove decal from water with tweezers.
  • Gently lift decal off of paper backing with tweezers.
  • Place decal in desired location on model, adjusting with cotton swab if necessary.
  • Apply Mark Setter or Mark Softer as needed.

RM18.90
img
SAVERM13.90

HG 1/100 VF-31S Siegfried (Arad Molders') Special Water Transfer Decal

These waterslide decals were made especially for Bandai's 1/100-scale HG model kit of the VF-312S Siegfried piloted by Arad Molders from "Macross Delta"! 

The set is compatible with all three forms: Battroid, Gerwalk, and Fighter. Order yours today!

RM28.00

Showing 421 - 450 of 498 products