Price Clear







METAL PARTS

Showing 1 - 30 of 137 products

img
SAVERM9.60

[Metal Part] MG 1/100 RX-0 Unicorn Gundam 02 Banshee Ver.Ka Metal Enhancement Part Set

All pictures shown are for illustration purpose only. Actual product may vary, kindly check from the list below to find out the actual parts quantity.

Index         Parts                                                        Installation Instruction
1.                 Back Pack Thruster                               drill 1.5mm hole, attached to point with minor cement
2.                     Elbow Joint Screw                               drill 2.0mm hole, attached to point with minor cement
3.                     Knee Joint Screw                                 drill 2.0mm hole, attached to point with minor cement
4.                     Back Thruster                                        drill 1.5mm hole, attached to point with minor cement
5.                     Leg Thruster                                           drill 1.5mm hole, attached to point with minor cement
6.                     Flat Head Screw                                   drill 2.0mm hole, attached to point with minor cement
7.                     Aviation hole                                          drill 2.0mm hole, attached to point with minor cement

- Packages parts packed in different sealed plastic bags to avoid scratch, and easier installation (based on numbers tagged on the plastic bag)

- Model kits in pictures are only for illustration of finished metal parts installation and excluded in the package


Tools needed for assembling metal parts:
- Tweezer straight/angled
- Modelling kits cutter
- Metal cutter
- Metal wire 
- Plastic model kits cement
- Magnifying glass

RM62.40
img
SAVERM6.20

[Metal Part] Metal Thruster / Vents for Gundam Kit (C2, Red) (2 Units)

[Metal Part] Red Metal Thruster Vents (C2)

  • Specifications : Maximum diameter 6.5mm, Height 2.0mm, Joint hole Diameter 1.5mm
  • Joint stick : 3.0mm
  • 2 units (1 pair) per package
  • Contain 2 parts: External part is Sliver plated, Internal part is Red plated
  • Material: Diecast
  • Stainless
Installation guide:

1)Requires drilling works to create a joining point (3mm)
2)Apply cement to ensure the center joint tightened

RM7.80
img
SAVERM2.05

[Metal Part] Stainless Steel Spring Tube - 2mm (1 Unit)

[Metal Part] Stainless Steel Spring Tube for Customization 


Spec : Diameter : 2 mm , Tube Length : 120 mm

RM1.95
img
SAVERM2.05

[Metal Part] Stainless Steel Spring Tube - 2.5mm (1 Unit)

[Metal Part] Stainless Steel Spring Tube for Customization 


Spec : Diameter : 2.5 mm , Tube Length : 150 mm

RM1.95
img
SAVERM2.05

[Metal Part] Stainless Steel Spring Tube - 3mm (1 Unit)

[Metal Part] Stainless Steel Spring Tube for Customization 


Spec : Diameter : 3 mm , Tube Length : 200 mm

RM1.95
img
SAVERM4.00

[Metal Part] Stainless Steel Customize pile piling, hydraulic pipe - 2.0 mm (30 units)

Stainless Steel Customize pile piling, hydraulic pipe

Spec:Diameter 2.0 mm , Length 15 mm 

Quantity :30 Pipe

RM8.00
img
SAVERM4.00

[Metal Part] Stainless Steel Customize pile piling, hydraulic pipe - 2.5 mm (30 units)

Stainless Steel Customize pile piling, hydraulic pipe

Spec:Diameter 2.5 mm , Length 15 mm 

Quantity :30 Pipe

RM8.00
img
SAVERM4.00

[Metal Part] Stainless Steel Customize pile piling, hydraulic pipe - 3.0 mm (30 units)

Stainless Steel Customize pile piling, hydraulic pipe

Spec:Diameter 3.0 mm , Length 15 mm 

Quantity :30 Pipe

RM8.00
img
SAVERM3.60

[Metal Part] 4mm Zaku metallic Lens - Blue Colour

  • Diameter: 4.0mm
  • Blue colour lens
  • Thickness: 2.6mm
  • Material: Copper
  • Suitable to fit on Bandai MG zaku 2.0 model kits
  • Glue required

RM2.40
img
SAVERM3.60

[Metal Part] 4mm Zaku metallic Lens - Black Colour

  • Diameter: 4.0mm
  • Black colour lens
  • Thickness: 2.6mm
  • Material: Copper
  • Suitable to fit on Bandai MG zaku 2.0 model kits
  • Glue required

RM2.40
img
SAVERM35.50

[Metal Part] PG 1/60 RX-0 Unicorn Gundam Metal Enhancement Part Set

[Metal Part] PG 1/60 RX-0 Unicorn Gundam Metal Enhancement Part

Manual is available in chinese language.

All pictures shown are for illustration purpose only. Actual product may vary, kindly check from the list below to find out the actual parts quantity.


Index         Parts                                                        Installation Instruction
1.                 Head Vulcan Gun  x 2                            Cut off the plastic part and apply super glue for positioning
2.                     Arm Joint Screw   x 4                            drill 2.0mm hole, attached to point with minor super glue
3.                     Knee Joint Screw  x 4                           drill 2.0mm hole, attached to point with minor super glue
4.                     Foot Screw  x 4                                        drill 2.0mm hole, attached to point with minor super glue
5.                     Backpack Thruster  x 4                         drill 2.0mm hole, attached to point with minor super glue
6.                     Black Skirt Thruster   x 2                      drill 2.0mm hole, attached to point with minor super glue
7.                     Leg Thruster  x 2                                      drill 2.0mm hole, attached to point with minor super glue
8.                     Weapon Screw x 2                                   drill 2.0mm hole, attached to point with minor super glue
9.                     Backpack Screw x 4                                drill 2.5mm hole, attached to point with minor super glue
10.                   Backpack Aviation Hole x 4                 drill 2.5mm hole, attached to point with minor super glue
11.                   Body Aviation Hole X 6                           drill 2.5mm hole, attached to point with minor super glue
12.                   Front Skirt Aviation Hole x 4                drill 2.5mm hole, attached to point with minor super glue
13.                   Leg Aviation Hole x 16                             drill 2.5mm hole, attached to point with minor super glue
14.                   Additional Flat Head Screw x 30          drill 2.5mm hole, attached to point with minor super glue



- Packages parts packed in different sealed plastic bags to avoid scratch, and easier installation (based on numbers tagged on the plastic bag)


- Model kits in pictures are only for illustration of finished metal parts installation and excluded in the package


Tools needed for assembling metal parts:
- Tweezer straight/angled
- Drill
- Super Glue
- Modelling kits cutter
- Metal cutter
- Metal wire 
- Plastic model kits cement
- Magnifying glass

RM84.50
img
SAVERM7.90

[Metal Part] Metal Thruster / Vents for Gundam Kit (B7, Blue) (2 Units)

[Metal Part] Blue Metal Thruster Vents (B7) (2units)

  • Specifications: Maximum diameter 12 mm, Height 12 mm, Joint diameter 2 mm
  • 2 units per package.

RM9.10
img
SAVERM6.20

[Metal Part] Metal Thruster / Vents for Gundam Kit (B1, Blue) (2 Units)

[Metal Part] Blue Metal Thruster Vents (B1)

  • Specifications: Maximum diameter 6.0mm, Height 6.5mm, Joint Diameter 1.5mm
  • Thruster Pin : 3.0mm
  • 2 units (1 pair) per package
  • Contain 2 parts: External part is Sliver plated, Internal part is Blue plated
  • Material: Diecast
  • Stainless
Installation guide:
    1)Requires drilling works to create a joining point (1.5mm)
    2)Apply cement to ensure the center joint tightened

RM7.80
img
SAVERM9.20

[Metal Part] 5mm L Energy Cable Tubes Pipes Metal Parts (Silver)

5mm M Energy Cable Tubes Pipes Metal Parts

A brand-new, unused, unopened, undamaged item

Ring Diameter : 5mm
Color : Silver
Package include
- 20 units Energy Tube Ring
- 1 20 cm Spring pipe
 
(This product not include any figure)

RM10.40
img
SAVERM7.30

[Metal Part] 3mm S Energy Cable Tubes Pipes Metal Parts (Silver)

3mm (S size) Energy Cable Tubes Pipes Metal Parts

A brand-new, unused, unopened, undamaged item

Ring Diameter : 3mm
Color : Silver

Package include
- 20 units Energy Tube Ring
- 1 20 cm Spring pipe
 
(This product not include any figure)

RM9.10
img
SAVERM7.90

[Metal Part] Metal Thruster / Vents for Gundam Kit (B9, Blue) (2 Units)

[Metal Part] Blue Metal Thruster Vents (B9)

  • Specifications : Maximum diameter 12.0mm, Height 5.0mm, Joint hole Diameter 2.0mm
  • Thruster Pin : 5.0mm
  • 2 units (1 pair) per package
  • Contain 2 parts: External part is Sliver plated, Internal part is Blue plated
  • Material: Diecast
  • Stainless
Installation guide:

1)Requires drilling works to create a joining point (2.0mm)
2)Apply cement to ensure the center joint tightened

RM9.10
img
SAVERM3.20

[Metal Part] Metal Thruster / Vents for Gundam Kit (B11, Blue) (2 Units)

[Metal Part] Blue Metal Thruster Vents (B11)

  • Specifications : Maximum diameter 20.0mm, Height 13.0mm, Joint hole Diameter 2.0mm
  • Thruster Pin : 6.0mm
  • 2 units (1 pair) per package
  • Contain 2 parts: External part is Sliver plated, Internal part is Blue plated
  • Material: Diecast
  • Stainless
Installation guide:

1)Requires drilling works to create a joining point (2.0mm)
2)Apply cement to ensure the center joint tightened

RM20.80
img
SAVERM6.20

[Metal Part] Metal Thruster / Vents for Gundam Kit (N1, Silver) (2 Units)

[Metal Part] Sliver Metal Thruster Vents (N1)

  • Specifications : Maximum diameter 6.0mm, Height 6.0mm, Joint hole Diameter 1.4mm
  • 2 units (1 pair) per package
  • Contain 2 parts: External part and Internal part is Sliver plated
  • Material: Diecast
  • Stainless
Installation guide:

1)Requires drilling works to create a joining point (1.4mm)
2)Apply cement to ensure the center joint tightened

RM7.80
img
SAVERM4.30

[Metal Part] Metal Thruster / Vents for Gundam Kit (N2, Silver) (2 Units)

[Metal Part] Sliver Metal Thruster Vents (N2)

  • Specifications : Maximum diameter 8.0mm, Height 8.0mm, Joint hole Diameter 2.5mm
  • 2 units (1 pair) per package
  • Contain 2 parts: External part and Internal part is Sliver plated
  • Material: Diecast
  • Stainless
Installation guide:

1)Requires drilling works to create a joining point (2.5mm)
2)Apply cement to ensure the center joint tightened

RM11.70
img
SAVERM4.00

[Metal Part] Metal Thruster / Vents for Gundam Kit (N3, Silver) (2 Units)

[Metal Part] Sliver Metal Thruster Vents (N3)

  • Specifications : Maximum diameter 10.0mm, Height 10.0mm, Joint hole Diameter 2.5mm
  • 2 units (1 pair) per package
  • Contain 2 parts: External part and Internal part is Sliver plated
  • Material: Diecast
  • Stainless
Installation guide:

1)Requires drilling works to create a joining point (2.5mm)
2)Apply cement to ensure the center joint tightened

RM13.00
img
SAVERM3.70

[Metal Part] Metal Thruster / Vents for Gundam Kit (N4, Silver) (2 Units)

[Metal Part] Sliver Metal Thruster Vents (N4)

  • Specifications : Maximum diameter 12.0mm, Height 12.0mm, Joint hole Diameter 2.5mm
  • 2 units (1 pair) per package
  • Contain 2 parts: External part and Internal part is Sliver plated
  • Material: Diecast
  • Stainless
Installation guide:

1)Requires drilling works to create a joining point (2.5mm)
2)Apply cement to ensure the center joint tightened

RM14.30
img
SAVERM6.50

[Metal Part] Metal Thruster / Vents for Gundam Kit (N5, Silver) (2 Units)

[Metal Part] Sliver Metal Thruster Vents (N5)

  • Specifications : Maximum diameter 6.0mm, Height 3.0mm, Joint hole Diameter 1.5mm
  • 2 units (1 pair) per package
  • Contain 2 parts: External part and Internal part is Sliver plated
  • Material: Diecast
  • Stainless
Installation guide:

1)Requires drilling works to create a joining point (1.5mm)
2)Apply cement to ensure the center joint tightened

RM6.50
img
SAVERM4.60

[Metal Part] Joining Angle Detailing Enhancement Parts for MG 1/100 Model Kit

Joining Angle Detailing Enhancement Parts

- Maximum diameter : 9 mm 
- Part Long : 3.8 mm 
- Each set got 2 unit enhancement metal part 
- Total 4 sets per pack  

Suitable for Gundam Arm and Leg joining angle customization.

RM10.40
img
SAVERM7.90

[Metal Part] X1 Turbine Thruster for Gundam Kit (1 pair, 2 sets)

[Metal Part]  Metal Turbine Thruster for Gundam Kit (X1)

  • Specifications : Maximum diameter 9mm, Height 10mm, Joint hole Diameter 2.0mm
  • 2 sets (1 pair) per package
  • Contain 2 parts: External part and Internal part is Sliver plated
  • Material: Die-cast
  • Stainless
Installation guide:

1)Requires drilling works to create a joining point (2.0mm)
2)Apply cement to ensure the center joint tightened

RM9.10
img
SAVERM6.80

[Metal Part] Metal Thruster / Vents for Gundam Kit (G3, Silver) (2 Units)

[Metal Part]  Metal Thruster / Vents for Gundam Kit (G3, Silver)

  • Specifications : Maximum diameter 10mm, Height 10mm, Joint hole Diameter 1.3mm
  • 2 units (1 pair) per package
  • Contain 2 parts: External part and Internal part is Sliver plated
  • Material: Diecast
  • Stainless
Installation guide:

1)Requires drilling works to create a joining point (1.3mm)
2)Apply cement to ensure the center joint tightened

RM13.20
img
SAVERM6.50

[Metal Part] Metal Thruster / Vents for Gundam Kit (G1, Silver) (2 Units)

[Metal Part]  Metal Thruster / Vents for Gundam Kit (G1, Silver)

  • Specifications : Maximum diameter 6mm, Height 6mm, Joint hole Diameter 1.2mm
  • 2 units (1 pair) per package
  • Contain 2 parts: External part and Internal part is Sliver plated
  • Material: Diecast
  • Stainless
Installation guide:

1)Requires drilling works to create a joining point (1.2mm)
2)Apply cement to ensure the center joint tightened

RM11.50
img
SAVERM6.50

[Metal Part] Metal Thruster / Vents for Gundam Kit (G2, Silver) (2 Units)

[Metal Part]  Metal Thruster / Vents for Gundam Kit (G2, Silver)

  • Specifications : Maximum diameter 8mm, Height 8mm, Joint hole Diameter 1.3mm
  • 2 units (1 pair) per package
  • Contain 2 parts: External part and Internal part is Sliver plated
  • Material: Diecast
  • Stainless
Installation guide:

1)Requires drilling works to create a joining point (1.3mm)
2)Apply cement to ensure the center joint tightened

RM12.50
img
SAVERM6.20

[Metal Part] Metal Thruster / Vents for Gundam Kit (Y6, Gold) (2 Units)

[Metal Part]  Metal Thruster / Vents for Gundam Kit (Y6, Gold)

  • Specifications : Maximum diameter 15mm, Height 12mm, Joint hole Diameter 2.0mm
  • 2 units (1 pair) per package
  • Contain 2 parts: External part and Internal part is Sliver plated
  • Material: Die-cast
  • Stainless
Installation guide:

1)Requires drilling works to create a joining point (2.0mm)
2)Apply cement to ensure the center joint tightened

RM11.80
img
SAVERM7.20

[Metal Part] Metal Thruster / Vents for Gundam Kit (Y7, Gold) (2 Units)

[Metal Part]  Metal Thruster / Vents for Gundam Kit (Y7, Gold)

  • Specifications : Maximum diameter 12mm, Height 12mm, Joint hole Diameter 2.0mm
  • 2 units (1 pair) per package
  • Contain 2 parts: External part and Internal part is Sliver plated
  • Material: Die-cast
  • Stainless
Installation guide:

1)Requires drilling works to create a joining point (2.0mm)
2)Apply cement to ensure the center joint tightened

RM9.80
img
SAVERM11.50

[Metal Part] HG / MG Scale Gundam Model kit Metal Modification Bar / Stick (8 units)

HG / MG scale Gundam Model kit  Metal Tonic

* Detail Modification 
* Universal compatible
* Detail Bar / Pole Decorative Bar

Bar length : 10 mm
Joint Diameter : 1.0mm
8 units in the package

RM6.50

Showing 1 - 30 of 137 products