PRODUCTS

Price Clear







Brand

Availability

Showing 181 - 210 of 3805 products

Quick View
img
SAVERM3.99

MODO Clear Sky Blue M-044 18ML

  • contains 20ml
  • clear color
  • MODO Clear Sky Blue M-044 18ML
  • mixed together with lacquer thinner for model kit painting.

RM14.00
RM14.00 Add to cart
Quick View
img
SAVERM3.99

MODO Clear Green M-048 18ML

  • contains 18ml
  • MODO Clear Green M-048 18ML
  • mixed together with lacquer thinner for model kit painting.

RM14.00
RM14.00 Add to cart
Quick View
img
SAVERM5.09

MODO Clear Royal Blue M-049 18ML

  • contains 20ml
  • clear color.
  • MODO Clear Royal Blue M-049 20ML
  • mixed together with lacquer thinner for model kit painting.

RM12.90
RM12.90 Add to cart
Quick View
img
SAVERM10.98

MODO MX-07 BRONZE GOLD 18ML

  • contains 18ml
  • metal color
  • MODO BRONZE GOLD MX-07 18ML
  • mixed together with lacquer thinner for model kit painting.

RM19.00
RM19.00 Add to cart
Quick View
img
SAVERM8.90

Water Decal for MG 1/100 00 QAN[T] Gundam

- Water Decal for MG 1/100 00 QAN[T] Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
RM9.00 Add to cart
Quick View
img
SAVERM12.98

MODO MK-15 AURORA RED 18ML

  • contains 18ML
  • Limited special edition color
  • MODO MK-15 AURORA RED 18ML
  • mixed together with lacquer thinner for model kit painting.

RM23.00
RM23.00 Add to cart
Quick View
img
SAVERM6.97

MODO D-08 Retarder Max (250ML)

  • contains 250ML
  • used to mix with thinner and paints to slow down drying time. 
  • used in metallic paints to achieve smooth surface.
For those who still don't know how to use Modo for hand painting.
Here's the tip, mix your lacquer base paint (especially Modo paint) with D-08 Retarder Max. It is the best solvent to slow down the drying time and reduce the chances of leaving brush stroke.

RM35.00
RM35.00 Add to cart
Quick View
img
SAVERM8.90

Water Decal HG Beargguy III

- Water Decal for HG BEARGGUY III water decal
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
RM9.00 Add to cart
Quick View
img
SAVERM8.90

Water Decal HG 1/144 00 QAN[T] Gundam

- Water Decal for HG 1/144 00 QAN[T] Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
RM9.00 Add to cart
Quick View
img
SAVERM8.90

Water Decal for MG 1/100 GAT-X103 BUSTER Gundam

- Water Decal for MG 1/100 GAT-X103 BUSTER Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
RM9.00 Add to cart
Quick View
img
SAVERM19.98

Metal Alligator Clips with sticks for Spray works (20 units 1 set)

  • Metal Aligator Clips with wood sticks for Spray works 
  • Metal Aligator Clips comes with black colour glove around.
  • useful when you need an extra hand to hold the plastic model parts for spray.
  • 20 units in 1 set with affordable price; hurry to purchase while stock lasts.

RM16.00
RM16.00 Add to cart
Quick View
img
SAVERM26.97

Metal Alligator Clips with sticks for Spray works (30 units 1 set)

  • Metal Aligator Clips with wood sticks for Spray works 
  • Metal Aligator Clips comes with black/red colour glove around.
  • useful when you need an extra hand to hold the plastic model parts for spray.
  • 30 units in 1 set with affordable price; hurry to purchase while stock lasts.

RM21.00
RM21.00 Add to cart
Quick View
img
SAVERM299.64

HS08 Mini Airbrush Compressor (Piston Type) Combo with Air brush Pen (Free Basic Painting Tools)


  • Suitable for air brush 0.2mm - 0.5mm 
  • Auto start and stop function
  • Air pressure adjustable
  • Airbrush pen, 2 leg AC adapter (Input AC100~240V 50/60HZ 0.6A)
  • Auto start: 15psi
  • Auto stop: 25psi
  • Working pressure: 2- 15psi
  • Air flow : 10.5L / min
  • Airbrush pen type: Double Action Airbrush pen
  • 360 degree circumvention airbrush holder, for your convenient work
  • Package include Air humid filter
Free Basic Beginner Essential Painting Tools
  • 1 pair of Rubber Gloves
  • 1 x Paint Fine Tip Paint Brush
  • 1 x Paint Mixing Spoon
  • 2 x Paint Mixing Bottle 
  • 3 x Measuring Cups
  • 4 x Eye Dropper
  • 1 x 6 mm Masking Tape
  • 1 x Cotton Bud (50+ pcs)
  • 3 x Metal Dish
  • 10 x Alligator Clips

RM240.00
RM240.00 Add to cart
Quick View
img
SAVERM53.89

[Star Wars] 1/12 Boba Fett

[Star Wars] 1/12 Boba Fett


The most famous bounty hunter in the galaxy is now a 1/12 scale model kit from Bandai! It features the same detail and articulation that you've come to expect from the line,, and comes with a full array of accessories including interchangeable hand parts and a dedicated display base! Look for origin of shipment: only items shipped from within North America are being sold by authorized U.S. Retailers. The product box will have a Bluefin warning label, which is proof that you are purchasing an officially licensed band a I product, distributed by its sole and authorized distributor (Bluefin distribution) for the U.S. Markets. This product has been thoroughly tested for safety and meets all North American consumer product safety regulations. The affixed label with the Bluefin distribution logo also entitles the purchaser to product support assistance.

Accessories: only display base, jet pack, blaster rifle, blaster pistol, hand part four (right weapon possession, grip hands × 2, left open hand)

RM108.00
RM108.00 Add to cart
Quick View
img
SAVERM3.18

Tamiya Acrylic Paint Retarder (40ml)

  • This paint retarder will make acrylic paint dry slower, enabling a smoother finish. It can be used up to a 1:10 ratio with Tamiya Acrylic Paints. It helps to lessen the chance oｆ painting a grainy surface on your model. Also, it is ideal for painting glossy finish surfaces. 1 bottle contains 40ml.

RM20.80
RM20.80 Add to cart
Quick View
img
SAVERM10.90

Tamiya Liquid Surface Primer 40ml - White

  • The currently available Liquid Surface Primer is highly useful for filling seam lines and smoothing over scratches in small or difficult to reach areas since it can be applied with a modelling brush. However, since some modellers have found it difficult to paint over it with a lighter color, we now release this white-colored version of the liquid primer to solve this problem. 
  • You can also thin out the primer with Tamiya Lacquer Thinner for convenient application with airbrushes. Each bottle contains 40ml.

RM25.00
RM25.00 Add to cart
Quick View
img
SAVERM10.98

Tamiya Liquid Surface Primer 40ml - Gray

  • In order to smooth over small scratches etc., many modelers have created their own liquified putty by dissolving putty with lacquer thinner. Tamiya now makes this process a whole lot easier by releasing our very own liquified putty, Liquid Surface Primer. Just brush on over scratches, rough areas etc. and you will get that perfect smooth finish.
  • Applies easily to small areas using a modeling brush
  • Can be used on plastic, metal and wooden models
  • Can be further diluted using Tamiya Lacquer Thinner, allowing it to be used in airbrushes.
  • 1 bottle contains 40ml

RM25.00
RM25.00 Add to cart
Quick View
img
SAVERM3.98

Tamiya Color Acrylic Paint X-15 (Light Green) (23ml)

Tamiya Acrylic Paints are made from water soluble resins that are excellent for either brush or spray painting. They have excellent coverage and can be used on resin, styrofoam, wood, fiberglass and all common model plastics. The paint flows smoothly with no blushing or fading and colors can be blended very easily to achieve that realistic finish to bring your scale model to life.

Each bottle of Tamiya Acrylic Paints contains 23ml and there is a wide range of gloss, flat and translucent colors. There is also an exclusive thinner and flat base which when added to one of the gloss colors will turn it into a satin or flat finish depending on how much you use.

Specs:
Color Code: X-15
Type: Light Green
Volume: 23ml

Tips:
- When airbrushing make sure to use any of the following Tamiya thinners: 81020, 81030, 81040, 81520, 87077.
- X designated colors have a glossy finish while XF designated colors are flat finish.
- The paint can be thinned for airbrushing using Tamiya X-20A Acrylic thinner.
- The paint can be also thinned for airbrushing using Tamiya Lacquer Thinner. Using Tamiya Lacquer - Thinner will yield faster drying results and a harder finish.
- For better paint brushing results use Tamiya Paint Retarder (87114) for a smoother brushstroke free finish.

RM20.00
RM20.00 Add to cart
Quick View
img
SAVERM22.00

Mr Hobby Mr.Tools Mr.Nipper II Cutter MT104 ( Hobby Tools )

Entry level sprue cutter


Mr. Nipper is a dual-sided, all purpose, pre-lubricated cutting tool from Mr. Hobby. Featuring a spring-assisted reopening of the handles, and a comfortable curvature of the hand grips,  Mr. Nipper is going to be the cutting tool that makes cutting plastic feel rewarding. The blades are angled slightly upwards and are flat faced, giving you a guaranteed clean cut that gives a "snappy" response, rather than the nipper "chewing" through the gates. The added pressure also reduces the amount of discoloration where it was cut.

RM56.00
RM56.00 Add to cart
Quick View
img
SAVERM11.90

MODO Phantom Gold MK-37 20ML

  • contains 20ML of lacquer paint
  • COLOR: phantom gold MK-37
  • apply a dark black/gray surfacer such as MK-11 / MK-12 as first layer before applying the phantom paint.
  • after the surface is smooth u may mixed with MODO retarder max + any phantom series paint to make the surface gloss & shinny.

RM38.00
RM38.00 Add to cart
Quick View
img
SAVERM21.90

MODO Phantom Green MK-38 20ML

  • contains 20ML of lacquer paint
  • color: phantom green MK-38
  • apply a dark black/gray surfacer such as MK-11 / MK-12 as first layer before applying the phantom paint.
  • after the surface is smooth u may mixed with MODO retarder max + any phantom series paint to make the surface gloss & shinny.

RM38.00
RM38.00 Add to cart
Quick View
img
SAVERM9.97

MODO Phantom Red MK-35 20ML

  • apply a dark black/gray surfacer such as MK-11 / MK-12 as first layer before applying the phantom paint.
  • after the surface is smooth u may mixed with MODO retarder max + any phantom series paint to make the surface gloss & shinny.
  • contains 20ML gloss phantom red lacquer paint.

RM38.00
RM38.00 Add to cart
Quick View
img
SAVERM7.98

[Battleship Yamato] Mecha Colle 18 Yamato 2199: Deusura II Core Ship

Take command of your Mecha Colle Gamilas fleet with this small but well-detailed snap-fit kit of Dessler's command ship! Parts are molded in dark blue plastic.

RM16.00
RM16.00 Add to cart
Quick View
img
SAVERM25.95

1/144 System Weapon 010

- Popular [Mobile Suit Gundam SEED] systems Weapon bazooka and rifle is now a set for MS!

- [SEED] system MS recommended weapon appeared to Builders parts. Included bazooka, rifle can be customized, respectively.
- Grip correspond to an existing series of Possession (SEED system). Corresponding SEED system possession is also included.

- Accessories: Strike bazooka, beam rifle, customized parts for strike bazooka, customized for the beam rifle parts, dedicated rack, hand parts x set

* Gunpla is not included

RM52.00
RM52.00 Add to cart
Quick View
img
SAVERM17.18

Water Decal PG 1/60 FX-550 SKY GRASPER

- Water Decal for PG FX-550 SKY GRASPER water decal
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 21 cm x 24 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM18.80
RM18.80 Add to cart
Quick View
img
SAVERM13.98

Water Decal for PG 1/60 MBF-02 Strike Rouge Gundam

- Water Decal for PG 1/60 MBF-02 Strike Rouge Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11.5 cm x 13.5 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunpla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM10.00
RM10.00 Add to cart
Quick View
img
SAVERM8.90

Water Decal for RG 1/144 FX550 Sky Grasper

- Water Decal for RG 1/144 FX550 SKY GRASPER water decal
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
RM9.00 Add to cart
Quick View
img
SAVERM15.08

HG 1/144 STRIKE FREEDOM Metal Effect Water Decal

- Water Decal for HG 1/144 Strike Freedom Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 10 cm x 9 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM14.90
RM14.90 Add to cart
Quick View
img
SAVERM5.85

[Metal Part] Aviation Hole 2.5mm for HG / MG Gundam model kits - 15 units

  • 2.5mm diameter aviation hole.
  • Package include 15 units of aviation hole for modelling kits customization.
  • Thickness : 1.5 mm

RM7.15
RM7.15 Add to cart
Quick View
img
SAVERM22.18

[Metal Part] Zaku Metal shoulder thorn type ZC1 for HG / MG - 3 units

  • 3 units of zaku metal part shoulder throne type ZC 1.
  • Widest diameter: 9.7mm, length: 16.8mm
  • can fit with MG zaku modelling kits nicely and don't need any cement to be attach on the kit.

RM7.80
RM7.80 Add to cart

Showing 181 - 210 of 3805 products